Honda fit clutch replacement




Honda fit clutch replacement

Article Navigation:
  • Photo
  • How to fit a clutch on a Honda Jazz II - Professional Motor Mechanic
  • Video
  • RELATED PAGES
  • Author Topic: DIY Clutch Replacement - sorted (Read times) problem - must say something about Honda's build quality (or rather AP.

    If the thickness is less than the service limit, replace the clutch disc. If the race does not turn smoothly, quietly, or fit tight in the crankshaft, replace the pilot.

    Special Tools Required. Clutch Alignment Disc 07JAF-PMA; Clutch Alignment Shaft 07JAF-PMA; Clutch Alignment Shaft 07ZAF-PR8A; Ring Gear.

    Honda fit clutch replacement

    Honda fit clutch replacement

    Incorrect linkage or cable adjustment, and "riding" the clutch resting one's foot on the clutch pedal, not allowing the clutch to release completely can cause premature clutch failure. The engine will "rev" but speed will not increase or the vehicle may not move. How are clutch issues diagnosed? Changes in the Battery Market September 25, Install the flywheel on the crankshaft, and install the mounting bolts finger-tight.

    Honda fit clutch replacement

    Honda fit clutch replacement

    Honda fit clutch replacement

    Honda fit clutch replacement

    Honda fit clutch replacement

    Honda Fit Clutch Replacement Cost Estimate

    Check the diaphragm spring fingers for height using the dial indicater A. If the height is more than the service limit, replace the pressure plate. Install the special tools. To prevent warping, unscrew the pressure plate mounting bolts A in a crisscross pattern in several steps, then remove the pressure plate B. Inspect the pressure plate A surface for wear, cracks, and burning.

    Inspect the fingers of the diaphragm spring B for wear at the release bearing contact area. Inspect for warpage using a straight edge A and feeler gauge B. Measure across the pressure plate C. If the warpage is more than the service limit, replace the pressure plate. Remove the clutch disc and special tools. Inspect the lining of the clutch disc for signs of slipping or oil. If the clutch disc is burned black or oil soaked, replace it. Measure the clutch disc thickness. If the thickness is less than the service limit, replace the clutch disc.

    Honda fit clutch replacement

    Measure the rivet depth from the clutch disc lining surface A to the rivets B on both sides. If the rivet depth is less than the service limit, replace the clutch disc.

    Turn the inner race of the pilot bearing with your finger. The pilot bearing should turn smoothly and quietly. Check that the pilot bearing outer race fits tightly in the flywheel. If the race does not turn smoothly, quietly, or fit tight in the crankshaft, replace the pilot bearing. Remove the pilot bearing A using the special tools. Install the new pilot bearing A into the crankshaft using the special tools. Apply a light coat of oil to the bearing surface.

    Honda fit clutch replacement

    Inspect the ring gear teeth for wear and damage. Inspect the clutch disc mating surface on the flywheel for wear, cracks and burning. Measure the flywheel A runout using a dial indicator B through at least two full turns with the engine installed. Push against the flywheel each time you turn it to take up the crankshaft thrust washer clearance.

    If the runout is more than the service limit, replace the flywheel and recheck the runout. Resurfacing the flywheel is not recommended. Install the special tool. Remove the flywheel mounting bolts in a crisscross pattern in several steps, then remove the flywheel. Install the flywheel on the crankshaft, and install the mounting bolts finger-tight. Install the special tool, then torque the flywheel mounting bolts in a crisscross pattern in several steps.

    Install the ring gear holder. Install the pressure plate A and the mounting bolts B finger-tight. Torque the mounting bolts in a crisscross pattern. Tighten the bolts in several steps to prevent warping the diaphragm spring. Remove the special tools. Make sure the diaphragm spring fingers are all the same height.

    Honda fit clutch replacement

    Remove the release fork A from the clutch housing B by squeezing the release fork set spring C with pliers. Remove the release bearing D. Check the release bearing for play by spinning it by hand.

    If there is excessive play, replace the release bearing with a new one. The release bearing is packed with grease. Do not wash it in solvent. With the release fork slid between the release bearing pawls, install the release bearing on the mainshaft while inserting the release fork through the hole in the clutch housing.

    EXEDY Tech - Manual Clutch Replacement procedures and precautions



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲